1) Invest in the correct tools: Having the right tools is critical to complete any task. You will need an extension ladder in height enough to achieve the highest gutter on your house, unless your roof has a shallow enough pitch that you feel at ease walking on it to print on higher gutters. We also recommend using a ladder stand-off to stabilize the ladder, as well as to hold the ladder off of your gutters and prevent from damaging them. Bring a hammer so you are able to re-nail any loose gutter spikes, a long hose, Gloves, a leaf blower to clear off roof debris, a drill with the correct 1/4′ hex head bit to disassemble downspouts if needed, and a clean out tool for the downspouts. The top elbow section of each downspout is the most vulnerable point for collecting and trapping debris. Bringing a 2′ flexible pipe cleaner to snake out the top part of a clogged downspout and avoid having to disassemble the downspout to eliminate the clog.

Recommended–> : Gutter Cleaning
2) Remove all accessible roof debris: Start with the highest part of the roof first and work your way down. A leaf blower really comes in handy here. The last thing you must do is thoroughly clean all of your gutters and then have the accumulated debris from your roof fill them up again.

Three) Inspect your roof: While you’re up on your roof clearing debris, it’s a great moment to inspect your roof, and it’s easier than you might think. A) Check for soft spots in the roof. While you are walking you may notice sunken in, distorted, or soft spots in your roof. These could be symptoms of possible water intrusion or even attic ventilation issues. Examine the area around and above the noticed area for punctures in the top or missing shingles. B) Visually inspect the roof for missing/damaged shingles. Moreover , note the age and general condition of the shingles. The regular shingle has a 25 year life expectancy. As shingles age they are going to become thin as they lose what most people refer to as shingle grit, which you also may notice accumulating in the gutter of yours. C) Check all penetrations in your roof as fan, dryer, and plumbing vents. It is pretty common for the rubber gaskets around pipe vents to dry-rot and leak. You are able to buy a couple more years out of the pipe collar by sealing around the dry rotted rubber gasket with a good roofing cement.

4) Clean & clear your gutters and downspouts: Start by removing the debris out of your gutters by hand (don’t forget your gloves!). Just like your roof you would like to start with probably the highest gutters first. You can bag the trash as you go on the roof but for safety reasons we recommend merely throwing it down on the ground. It is much easier and safer to bag it on the ground. When throwing it down from the roof, try to throw it into piles to make clean-up easier. After you have eliminated the top stuff by hand we recommend flushing out the small debris and shingle grit left behind with a water hose. This will also help make sure that the downspouts are clear of debris at the same time. When working with a water hose it’s crucial that you discover exactly where the hose is at all times. A water hose that’s left dangling from the top can cause havoc on the landscape of yours, etc., flags, lawn ornaments, when moving around on the roof. Start with probably the highest gutters at the opposite end of the outlet/downspout. Work the debris to and down the downspout. Check the bottom of the downspout to make sure water is draining properly. If the gutter backs up with water then maybe you have a clogged downspout. Use your downspout tool in an attempt to snake any clogs that could be at the high elbow section of the downspout. If that does not work because the downspout is too severely clogged, or the clog is far down the downspout, dissembling the downspout may be essential.

5) Inspect your gutters: Make certain your gutters are draining properly. Gutters that are holding water are more vulnerable to collecting debris, perfect breeding grounds for mosquitoes and other insects, can deteriorate the sealant in end caps, outlets, and miters, and can pull gutters from the fascia because of the added weight. If after flushing your gutters with water, the downspout is simply not clogged but the gutter is holding water, your gutter may have to be replaced or perhaps re-pitched properly towards the outlet. This could happen as a result of bent or distorted gutters from improper maintenance or perhaps snow accumulation, natural settling of the house, if not a poor initial installation. Make certain your gutters are secured tightly to the fascia boards. Now days most gutters are installed utilizing an internal bracket which is screwed to the fascia board and is not going to pull loose. Nonetheless, a great deal of individuals will find that their gutters were installed using what’s known as a spike and ferrule.With the weight of debris and snow accumulation these spikes have a tendency to pull free from the fascia board that can cause fascia rot and even total collapse of the gutter. We recommend re-nailing any loose gutter spikes when cleaning the gutters of yours. Using your hammer simply tap on each spike head until the gutter sets firmly to the fascia. You might notice the spike does not hold and seems loose or even keeps pulling away. If this happens call a professional to evaluate your gutters.

When finished with your gutter cleaning, be sure you do not leave any tools up on the roof. If you discover some challenges with your roof and/or gutters call a professional instantly to stay away from any costly water related damage that might end up in the future. We recommend completing this important home maintenance no less than two times a year, one time in the spring and once again in the fall. Nonetheless, every home is going to vary and you ought to modify your gutter cleaning schedule accordingly.